1-2-1-tekhnicheskie-dannye.html
1.2.1. Specifications
Name
|
Nominal rates |
Gazoraspredeleniye phases
|
– inlet valve |
|
6 |
|
46 |
– final valve
|
|
44 |
|
8 |
Overlapping of valves |
14 |
Duration of opening of the inlet valve |
232 |
Duration of opening of the final valve |
232 |
Height of cams of a camshaft, mm |
43,95–44,15 |
Diameter of necks of a camshaft, mm |
25,967–25,980 |
Oil gap in the bearing of sliding of a camshaft, mm |
0,020–0,061 |
Axial люфт camshaft, mm |
0,1–0,15 |
Head of the block of cylinders
|
– a deviation from planeness of a privalochny surface, mm |
0,03 |
– a deviation from planeness of a privalochny surface of a collector, mm |
0,15 |
The repair sizes of an opening for installation of the directing plug of inlet and final valves, mm
|
- increased by 0,05 mm |
11,050–11,068 |
- increased by 0,25 mm |
12,250–11,268 |
- increased by 0,50 mm |
12,500–11,518 |
The repair sizes of an opening for installation of a saddle of the valve, mm
|
- inlet valve
|
|
33,300–33,325 |
|
33,600–33,625 |
- final valve
|
|
28,600–28,621 |
|
28,900–28,921 |
Length of the valve, mm
|
– inlet valve |
96,1 |
– final valve |
97,15 |
Diameter of a core of the valve, mm |
– inlet valve |
5,965–5,980 |
– final valve |
5,950–5,965 |
Corner of a working facet of the valve |
45–45,5 |
Width of a working facet, mm |
– inlet valve |
1,0 |
– final valve |
1,3 |
Gap between a core of the valve and the directing plug, mm |
– inlet valve |
0,020–0,050 |
– final valve |
0,050–0,065 |
Length of a spring of the valve without loading, mm |
45,5 |
Length of a spring of the valve under loading of 21,9 kg, mm |
35 |
Deviation of a spring of the valve from vertical situation, ° |
less than 1,5 |
Diameter of the piston, mm |
3,98–84,91 |
Gap between the piston and the cylinder, mm |
0,010–0,030 |
Width of a groove in the piston, mm |
– ring No. 1 |
1,230–1,250 |
– ring No. 2 |
1,220–1,240 |
– maslosjemny ring |
2,515–2,535 |
Repair sizes of pistons, mm |
0,25, 0,5, 0,75, 1,00 |
Gap in locks of piston rings, mm |
– ring No. 1 |
0,20–0,35 |
– ring No. 2 |
0,37–0,52 |
– maslosjemny ring |
0,2–0,7 |
Lateral gap of piston rings, mm |
– ring No. 1 |
0,04–0,08 |
– ring No. 2 |
0,03–0,07 |
Repair sizes of piston rings, mm |
0,25, 0,50, 0,75, 1,00 |
Bend of a rod, mm on 100 mm of length |
0,05 |
Rod torsion on 100 mm of length, mm |
0,1 |
Lateral gap between the bottom head of a rod and cranked shaft, mm |
0,10–0,25 |
Effort of a press fitting of a piston finger, N |
2450–12255 |
Gap of the loose leaf of the shatunny bearing, mm |
0,018–0,036 |
Diameter of a shatunny neck
of a cranked shaft, mm |
47,982–48,000 |
Diameter of a radical neck of a cranked shaft, mm |
61,982–62,000 |
Deviation from a form of a circle of necks of a cranked shaft, mm |
less than 0,030 |
Konusnost of necks of a cranked shaft, mm |
less than 0,005 |
Axial люфт cranked shaft, mm |
0,070–0,250 |
Gap of the loose leaf of the radical bearing, mm |
0,004–0,022 |
Diameter of the cylinder, mm |
84,00–84,03 |
Deviation from planeness of a privalochny surface
of the block of cylinders, mm |
less than 0,03 |
Deviation from a form of a circle and a konusnost of the cylinder, mm |
less than 0,02 |
Moments of an inhaling of carving connections, N • m
Bolt of fastening of a pulley of a cranked shaft |
180–190 |
Bolt of fastening of the mechanism of a tension of a gear belt |
20–27 |
Bolt of fastening of a pulley of a camshaft |
20–27 |
Bolts of fastening of a cover of a head of the block of cylinders |
8–10 |
Bolts of fastening of a cover of the radical bearing
|
|
27–33 + (90 °–94 °) |
|
14–18 + (90 °–94 °) |
Bolts of fastening of a cover of a rod |
16–20 + (90 °–94 °) |
Bolts of fastening of a head of the block of cylinders (the cold engine) |
25 + (60 °–64 °) + (45 °–49 °) |
Drain stopper of the oil pallet |
35–45 |
Bolts of fastening of the bottom section of the oil pallet |
10–12 |
Bolts of fastening of the top section of the oil pallet
|
|
30–42 |
|
19–28 |
|
5–7 |
|
5–7 |
Bolt ы fastenings of the mesh oil filter |
15–22 |
Bolts of fastening of the oil pump |
12–15 |
Stopper of a safety valve |
40–50 |
Sensor of pressure of oil |
8–12 |
Screw of fastening of a cover of the oil pump |
8–12 |
Oil filter |
17–25 |
Plate of a drive and transitional plate |
73–77 |
The ignition distributor to the engine |
12–15 |
Bolts of fastening of the air filter |
8–12 |
Resonator support |
15–20 |
Nuts of fastening of the resonator to an inlet collector |
15–20 |
Bolts of fastening of the resonator to an inlet collector |
15–20 |
Nuts and bolts of fastening of an inlet collector |
19–21 |
Bolt of fastening of the filter to a final collector |
12–15 |
Nuts and bolts of fastening of a final collector |
25–30 |
Directing pipe oil щупа to the engine |
12–15 |
Bolts of fastening of the union of an exit of cooling liquid |
17–20 |
Bolts of fastening of an arm of the oil pump to a head of the block of cylinders |
|
The oil pump of the amplifier of a steering drive to an arm |
17–26 |
Sensor of an angle of rotation of a cranked shaft |
11–12 |
Bolt of fastening of a support of the engine (12х115) |
90–110 |
Nuts of fastening of an arm of a support of the engine |
60–80 |
Bolts of fastening of an arm of a support of the engine (12х60) |
60–80 |
Bolts of fastening of a stopper of a forward arm to a podmotorny frame |
60–80 |
Bolts and nuts of fastening of a support of a forward stopper (10х85 mm) |
50–65 |
Bolts of fastening of a support of a forward stopper to a transmission |
60–80 |
Bolts of fastening of a support of a back stopper to the bottom frame |
50–65 |
Bolts and nuts of fastening of a support of a back stopper |
50–65 |
Bolts of fastening of an arm of a support of a back stopper to a transmission |
60–80 |
Nuts of fastening of a transmission to an additional arm |
60–80 |
Nuts of fastening of a transmission to an additional arm |
60–80 |
Bolts of fastening of a transmission to a support (12х115 mm) |
90–110 |
Bolts of fastening of a starter |
27–34 |
Inlet pipe of the generator to a head of the block of cylinders |
12–15 |
Clip of a hose of supply of fuel to a head of the block of cylinders |
12–15 |
Clip of a hose of supply of fuel to a head of the block of cylinders |
10–12 |
Back plate |
8–10 |
Case of oil consolidation |
10–12 |
Bolt of fastening of a casing of a gear belt |
10–12 |
Bolt of fastening of an eye to the engine |
20–27 |
Arm of fastening of the generator to the engine |
20–30 |
Nuts of fastening of the generator |
20–30 |
Bolt of fastening of the generator to an arm |
20–30 |
Nuts of fastening of a starter |
20–30 |
Bolt of fastening of a belt pulley |
35–55 |
Bolt of fastening of the tension device of a driving belt |
20–27 |
Bolt of fastening of a support of the generator |
20–25 |
The water pump to the block of cylinders (a bolt with a label "7") |
15–22 |
The sensor of level of temperature of cooling liquid |
10–12 |
The sensor of temperature of cooling liquid |
20–40 |
Bolts of fastening of the union of an exit of cooling liquid |
10–15 |
Bolts of fastening of the air filter |
8–10 |
Nuts of fastening of an inlet collector to a head of the block of cylinders |
19–21 |
Throttle knot to the resonator |
15–20 |
Nuts of fastening of a final collector to a head of the block of cylinders |
25–30 |
The heat-shielding screen to a final collector |
12–15 |
The oxygen sensor to a final collector |
40–50 |
Nuts of fastening of a forward exhaust pipe to a final collector |
40–50 |
Bolts of fastening of a forward exhaust pipe to catalytic converter |
40–60 |
Nuts of fastening of the central exhaust pipe to catalytic converter |
40–60 |
Bolts of fastening of the central exhaust pipe to the main exhaust silencer |
30–40 |
Bolts of fastening of a rubber suspension bracket to the main exhaust silencer |
10–15 |
Bolts of fastening of the delivery pipeline |
10–15 |
|
|