Corners of installation of forward wheels. KIA Magentis/Optima (since 2000 of release)
Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
9. Power shafts, axes
10. Suspension bracket
10.1. Specifications
10.2. Rack of a forward suspension bracket
10.3. Bottom lever of a forward suspension bracket
10.4. Top lever of a forward suspension bracket
10.5. Shock-absorber of a back suspension bracket
10.6. Replacement of the top lever of a back suspension bracket
10.7. Replacement of the longitudinal lever of a back suspension bracket
10.8. Replacement of the supporting lever of a back suspension bracket
10.9. Replacement of the central lever of a back suspension bracket
10.10. Replacement of draft of the back stabilizer of cross-section stability
10.11. Corners of installation of forward wheels
10.12. Adjustment of a convergence of back wheels
10.13. Disorder of back wheels
10.14. Wear of tires
10.15. Wheel palpation
10.16. Search and elimination of malfunctions
11. Steering
12. Brake system
13. Body
14. Central air
15. Electric equipment
16. Electric circuits
 










10-11-ugly-ustanovki-perednikh-koles.html

10.11. Corners of installation of forward wheels

Check of corners of installation of forward wheels is necessary for carrying out at the special stand, thus the car should be in horizontal situation with the forward wheels established for rectilinear movement. Previously be convinced that the forward suspension bracket and a steering are in a normal state, tires and wheels have no defects.

Convergence

The convergence is defined as a difference of distances (V-and) between lobbies and back boards of rims of wheels. The positive convergence means that wheels are in front located more closely to each other, than behind, at measurement at height of an average point of a wheel. If the convergence does not correspond to demanded value, weaken the left and right lock-nuts of tips of steering drafts, then, rotating drafts, establish demanded corners. Tighten lock-nuts.

  • Positive convergence (B – A):–3 mm … +3 mm
  • Positive convergence (a+b):–17'11" … +17'11"

Turn on 1/2 turns of connecting drafts changes a positive convergence approximately to 4,8 mm (57 '40").

Turn on 1 turn of connecting drafts changes a positive convergence approximately to 9,6 mm (1°55 '20").

  1. Adjustment of a convergence should be carried out by rotation of the left and right tip of steering draft on an identical corner.
  2. At adjustment of a convergence weaken an external collar of fastening of a protective cover to prevent its twisting.
  3. After adjustment tighten lock-nuts of tips of steering drafts and collars of fastening of covers.

Inhaling moment: 50–55 N • m

Disorder

Disorder is a tilt angle of a wheel in relation to a paving in the vertical plane. It can be positive if wheels are inclined outside, or negative if wheels are inclined inside. The corner of disorder is established when manufacturing the car and cannot be regulated.

Disorder :

  • 0 °± 30' for a usual suspension bracket
  • 8 '± 30' for a high suspension bracket

Corner of a longitudinal inclination шкворня

The corner of a longitudinal inclination шкворня is established when manufacturing the car and cannot be regulated. If the corner of a longitudinal inclination шкворня does not correspond to demanded values, replace the pognuty or damaged details.

Corner of a longitudinal inclination шкворня: 3°15 '±1 °


  1. Before check and adjustment of corners of installation of wheels the forward suspension bracket should be free from the worn-out, free or damaged details.
  2. Adjustment of corners of installation of wheels is necessary for carrying out, using the special tool 09529-21000.
  3. Disorder and corner of a longitudinal inclination шкворня are established when manufacturing the car and cannot be regulated.
  4. If disorder and a corner of a longitudinal inclination шкворня do not correspond to demanded values, replace the pognuty or damaged details.

«on a step back
10.10. Replacement of draft of the back stabilizer of cross-section stability
on the following page»
10.12. Adjustment of a convergence of back wheels