Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
9. Power shafts, axes
10. Suspension bracket
10.1. Specifications
10.2. Rack of a forward suspension bracket
10.3. Bottom lever of a forward suspension bracket
10.4. Top lever of a forward suspension bracket
10.5. Shock-absorber of a back suspension bracket
10.6. Replacement of the top lever of a back suspension bracket
10.7. Replacement of the longitudinal lever of a back suspension bracket
10.8. Replacement of the supporting lever of a back suspension bracket
10.9. Replacement of the central lever of a back suspension bracket
10.10. Replacement of draft of the back stabilizer of cross-section stability
10.11. Corners of installation of forward wheels
10.12. Adjustment of a convergence of back wheels
10.13. Disorder of back wheels
10.14. Wear of tires
10.15. Wheel palpation
10.16. Search and elimination of malfunctions
11. Steering
12. Brake system
13. Body
14. Central air
15. Electric equipment
16. Electric circuits
 










10-2-stojjka-perednejj-podveski.html

10.2. Rack of a forward suspension bracket

Removal

 PERFORMANCE ORDER

1. Remove a forward wheel.

2. Separate a brake hose from a fork.

3. Turn out a bolt of fastening of a fork of the shock-absorber.

4. Turn out a bolt and get a fork from the shock-absorber.

5. Turn out three nuts of fastening of the top part of a rack.

6. Moving up, remove a rack of a forward suspension bracket.

Installation

 PERFORMANCE ORDER

1. Place an arm of a fork of a forward rack about an internal part of the car, then establish a rack in a wheel arch.

2. Establish a fork to a rack.

3. Establish a brake hose.
4. Establish a wheel.

Dismantling

 PERFORMANCE ORDER

1. The special adaptation compress a spring of a rack of a forward suspension bracket.

  1. Do not tighten breakthroughs an adaptation nut for spring compression
  2. Turn out самоконтрящиеся nuts.
  3. Remove the special tool, an arm, elastic laying and a cylindrical spring.

Check

 PERFORMANCE ORDER

1. Check rubber details on absence of damages or deterioration of their condition.
2. Check a cylindrical spring on lack of a deflection and elasticity loss.

3. Check operability of the shock-absorber.

Before utilization of the shock-absorber remove from it gas.

Shock-absorber utilization

 PERFORMANCE ORDER

1. Completely extend a shock-absorber rod.

2. Drill an opening to remove gas from the cylinder.

Gas leaving the shock-absorber is safe, however it is necessary to be careful not to be traumatized from taking-off shaving.

Assembly

 PERFORMANCE ORDER

1. The special adaptation compress a spring of a rack of a forward suspension bracket. After complete compression of a spring establish it on the shock-absorber.

  1. Do not tighten breakthroughs an adaptation nut for spring compression
  2. Make the chart of installation of springs.

Left spring Right spring

White color White color

Yellow Yellow

Red color Red color

2. Establish a dustproof cover, the top laying of a spring, the plug (B), an arm, the plug (A) and by hand tighten new самоконтрящиеся nuts.

3. Establish the top and bottom ends of a cylindrical spring in the top elastic laying and in the bottom nest of a spring.

4. Turn an arm that the bolt of fastening of an arm was on a straight line to a projection of a vilochny arm.

5. Remove the special tool.

6. Tighten a nut of fastening of a rod of the shock-absorber the moment of the inhaling given in the specification.

Inhaling moment : 20–25 N • m


«on a step back
10.1. Specifications
on the following page»
10.3. Bottom lever of a forward suspension bracket