11-11-rulevaya-kolonka-rulevojj-val.html
11.11. Steering column / helmsman shaft
Removal
|
|
1. Turn out self-cutting screws and remove the button of a sound signal. |
|
2. Unscrew a nut of fastening of a steering wheel and remove a washer.
|
Before performance of these procedures look section of «SRS safety cushion».
|
|
3. Put combination labels on an end face of a steering shaft and a steering wheel and a stripper remove a steering wheel.
|
Do not knock on a steering wheel as these can damage a steering column.
|
|
4. Turn out screws and remove casings of a steering column. |
5. Remove the bottom cover.
|
6. Disconnect electric sockets and remove the multipurpose switch. |
|
7. Turn out a bolt connecting the universal hinge and a shaft of a gear wheel of steering transfer. |
8. Turn out bolts of fastening of a dustproof cover. 9. Turn out bolts of fastening of a steering column (4 bolts).
|
10. Remove a steering column and a shaft together with the universal hinge and a dustproof cover. |
|
|
Dismantling
|
|
1. Weaken a bolt of fastening of a steering shaft to the universal hinge and remove the universal hinge. |
2. Remove lubricant from an internal working edge of a cover.
|
3. With a core expand a working edge and remove a cover. |
4. Put a greasing layer on an internal working edge of a cover.
|
5. Cover the hinge, using a core for expansion of a working edge. |
|
6. With a core expand behind an internal cover and, having pulled, remove it from the hinge. |
7. If necessary remove the lock of a steering column, previously having cut through a hacksaw on metal grooves in heads of cut-off bolts. Unscrew bolts a screw-driver with a flat edge and remove the lock of a steering column.
|
At installation of the lock of ignition it is necessary to use new bolts with a cut-off head.
|
|
|
Check
|
1. Check a steering column and a steering shaft on absence of damages and deformations. 2. Check the universal hinge of a steering shaft on absence люфта, damages and jammings. 3. Check a tilt angle arm on lack of cracks and damages. 4. Check a protective cover on lack of cracks or damages. 5. Check operation of the mechanism of the lock of a steering column.
|
|
Assembly
|
1. At installation of a steering column, the lock of ignition and an arm of the lock of a steering column to a column pipe, temporarily put the lock of a steering column on one line with column inflow.
|
2. After check of operation of the lock of a steering column, tighten bolts with cut-off heads.
|
After installation of the lock of a steering column, the arm of the lock of a steering column and bolts should be replaced with the new.
|
|
|
3. Establish an internal working edge, a ledge of an internal cover with lubricant and pull outer side of a cover on the hinge.
|
4. Fill an internal part of the bearing with universal konsistentny greasing. 5. Establish the bearing on a hinge shaft.
|
6. Wrap up the bearing on 1,5 turns a vinyl tape and press the bearing in a cover. |
|
|
Installation
|
1. Before installation, put universal konsistentny greasing in a groove on an internal part of the bearing and interfaced surfaces of a cover and cover knot assembled. 2. Connect the lower part of a steering shaft and the hinge.
|
At installation at first fix the U-shaped hinge to steering transfer, then to a steering shaft.
|
3. Establish a dustproof cover with steering shaft. 4. Establish a steering column in collecting and fix four bolts. 5. Establish the multipurpose switch and connect sockets. 6. Establish the top and bottom casings of a steering column.
|
7. Establish a steering wheel.
|
At installation be careful not to damage a put steering shaft.
|
|
|
|
|
|