Power steering pump. KIA Magentis/Optima (since 2000 of release)

Magentis and Optima repair since 2000 of release
	1. Engines
	2. Greasing system
	3. Cooling system
	4. Control and decrease in toxicity
	5. Fuel system
	6. Ignition system
	7. Coupling
	8. Transmission
	9. Power shafts, axes
	10. Suspension bracket
	11. Steering
		11.1. Specifications
		11.2. Check of a free wheeling of a steering wheel
		11.3. Check of an angle of rotation of forward wheels
		11.4. Check of return of a steering wheel in a starting position
		11.5. Check of a torque of a pin of the spherical hinge of a tip of steering draft
		11.6. Check of level of liquid
		11.7. Liquid replacement in a hydraulic drive of the power steering
		11.8. Pumping of hydraulic system of the amplifier of a steering
		11.9. Check of a tension of a belt of a drive of the pump of the power steering
		11.10. Check of pressure of liquid in hydraulic system
		11.11. Steering column / helmsman shaft
		11.12. Steering transfer of cars with the power steering
		11.13. Power steering pump
		11.14. Power steering hoses
		11.15. Electronic system of the amplifier of a wheel
		11.16. Search and elimination of malfunctions of a steering
		11.17. Search and elimination of malfunctions of a steering of EPS
	12. Brake system
	13. Body
	14. Central air
	15. Electric equipment
	16. Electric circuits

11-13-nasos-gidrousilitelya-rulya.html

11.13. Power steering pump

Removal

PERFORMANCE ORDER

At service of the oil pump close the generator a polyethylene film.

1. Disconnect a pressure head hose from the pump.

At assembly, use a new sealing ring.

2. Disconnect soaking-up filter from the socket of absorption and merge liquid in the container.

At removal of the soaking-up filter close the generator a polyethylene film.

3. On the engine V 6 remove a driving belt.

4. On the DOHC engine weaken an adjusting bolt of the mechanism of a tension and remove a driving belt.

5. Turn out assembly bolts of fastening of the oil pump and disconnect the socket of the sensor of pressure.

Dismantling

PERFORMANCE ORDER

1. Remove soaking-up pipe and a sealing ring from the pump.

2. Remove a back cover with laying and pins.
3. Remove a statorny ring.
4. Remove a rotor and blades.

5. Remove a forward lateral plate.

6. Remove internal and external sealing rings.

7. Remove a spring.

At assembly it is necessary to use new laying and a sealing ring.

8. Unscrew a nut of fastening of a pulley and remove a spring washer.

9. Remove a pulley and a segment shponka.

10. Using special flat-nose pliers, remove a lock ring.

11. Squeeze out a pulley shaft with the bearing. If necessary use a kapron hammer.

12. Remove an oil sealing ring from the pump case.

At assembly it is necessary to use a new oil sealing ring.

13. Disconnect the socket from the case of the oil pump and remove a spring and a throttle.
14. Remove a sealing ring from the socket.

Do not assort a throttle.

15. Remove the switch of the oil pump.
16. Remove a spring and the coil.

17. Remove a sealing ring from the switch of the oil pump.

Check

PERFORMANCE ORDER

1. Clear all details of the pump the corresponding solvent.
2. If there are damaged details of the pump, replace the pump assembled.
3. If the pulley is damaged or deformed, replace it.
4. If there are leakages of liquid about a sealing ring, replace it.
5. If shlitsa of a shaft or a pulley are damaged or worn-out, replace the corresponding details.

Assembly

PERFORMANCE ORDER

1. Establish the switch of the oil pump.
2. Establish a throttle spring, the valve and the socket in the pump case.

Grease with a thin layer of liquid of the amplifier of a steering all replaced details, including oil consolidation and a sealing ring.

3. The special tool 09222-32100 establish oil consolidation in the pump case.

4. Softly insert assembly of a shaft and establish a lock ring.

5. Establish a pump pulley with a segment shponka.

6. Establish a spring both internal and external sealing rings.

7. Establish a forward lateral plate.

8. Insert pins into deepenings of the forward case, then establish a statorny ring, paying attention to the direction of its installation.

9. Establish a rotor so that labels on a rotor settled down from outside, an opposite forward part of the case.

10. Establish blades the rounded-off parts outside.

11. Establish laying and a back cover.
12. Tighten the absorption socket.

Installation

PERFORMANCE ORDER

1. Establish the pump to a pump arm.
2. Establish soaking-up filter.
3. Establish poliklinovy a belt and adjust its tension.
4. Connect a pressure head hose to the pump and the soaking-up filter with a tank.

Establish hoses so that they were not overwound and did not make contact with any other parts.

5. Fill in liquid.

The recommended liquid: PSF–3

6. Pump over a hydraulic drive of the amplifier of a steering.
7. Check the pressure created by the pump.
8. Establish other details taking into account the demanded moments of an inhaling.

«on a step back
11.12. Steering transfer of cars with the power steering

on the following page»
11.14. Power steering hoses