Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
9. Power shafts, axes
10. Suspension bracket
11. Steering
12. Brake system
12.1. Specifications
12.2. Anti-blocking system of brakes
12.3. Check and adjustment of provision of a pedal of a brake
12.4. Check of the vacuum amplifier of brakes
12.5. Pumping of hydraulic system of a drive of brakes
12.6. Pumping of hydraulic system of a drive of brakes with scanner use
12.7. Adjustment of a course of the parking brake
12.8. Brake pedal
12.9. Main brake cylinder
12.10. Vacuum amplifier of brakes
12.11. Brake tubes and hoses
12.12. Pressure regulator
12.13. Replacement of forward brake shoes
12.14. Support of a forward brake
12.15. Back drum-type brakes
12.16. Replacement of the working brake cylinder
12.17. Back disk brakes
12.18. Support
12.19. Hydraulic HECU block (the hydraulic and electronic control device)
12.20. Sensor of frequency of rotation of a wheel
12.21. Parking brake
12.22. Search and elimination of malfunctions
13. Body
14. Central air
15. Electric equipment
16. Electric circuits
 










12-21-stoyanochnyjj-tormoz.html

12.21. Parking brake

Removal

 PERFORMANCE ORDER

1. Remove the back console.

2. Remove the switch of the parking brake.
3. Remove the lever of the parking brake.

4. Disconnect the lever of the parking brake from a cable of the parking brake.

5. Remove back sitting, release and lift the top covering.
6. Remove a clip of a cable of the parking brake and condensing ring.
7. Move forward the thermofilter of the central exhaust silencer.
8. Turn out a bolt and remove a clip arm.
9. Remove a wheel and a brake drum.
10. Remove a back nave.
11. Remove springs and support of support of brake shoes.
12. Remove a cable clip.
13. Disconnect the cable end from a back brake shoe.

14. Extend a cable of the parking brake from an opening in a car body.

Check

 PERFORMANCE ORDER

1. Check operation of the switch of the parking brake.
2. Check on lack of wear a ratchet of the lever of the parking brake.
3. Check operability of a cable of the parking brake.

Installation

 PERFORMANCE ORDER

1. Check colors of marking of a cable of the parking brake (RH: White color, LR: Yellow color) also establish them according to the left and right parties.

2. Take away the regulator lever against the stop back at installation of a spring of fastening of a block to a block.

3. Establish condensing ring in the direction shown in drawing.

4. Grease a ratchet and a ratchet doggie.

Lubricant: SAE J310, NLGI No. 2

5. After installation of a regulator of a cable, adjust a course of the lever of the parking brake.

Adjustment

 PERFORMANCE ORDER

1. After replacement of the lever of the parking brake. Adjust a cable, having tightened the lever of the parking brake of 4-5 times.

2. After replacement of a cable of the parking brake.

  1. With back drum-type brakes.
    Adjust external diameter of brake shoes till the size of 227,6-228,1 mm.
    After installation of a brake drum adjust a cable of the parking brake.
  2. With back disk brakes.
    Get a stopper from a slip opening, then turn a regulator in the arrow direction for screw rotation (a flat screw-driver).
    Rotate a regulator on the whole 5 labels in relation to the counter direction of an arrow.

3. After replacement of brake shoes of a drum-type brake.

  1. Tighten the lever of the parking brake on 4 labels (or effort of 9 kg).
  2. Pass on the car distance of 400 m for speed of 50 km / h.
  3. Stop the car for 2 minutes.
  4. Repeat a step 2.
  5. Check a course of the parking brake.

«on a step back
12.20. Sensor of frequency of rotation of a wheel
on the following page»
12.22. Search and elimination of malfunctions