|
13-36-panel-priborov.html
13.36. Dashboard
On the dashboard the combination of devices, the central panel of furnish and a set of switches and control devices are placed
Central panel of furnish
The central panel of furnish represents a casing for the control panel heating and ventilation, a radio receiver, a ware box and forms the basis for the lighter and an ashtray. The central panel of furnish can remain on a place at dashboard removal.
Control switch of illumination of salon
The control switch of illumination of salon allows to regulate brightness of illumination of the dashboard.
Radio receiver
The radio receiver is located in the central panel. The aerial and electric sockets for connection of a radio receiver are located in a back part of a radio receiver. The wire of the aerial passes under the dashboard and connects the aerial to a radio receiver. Before dashboard removal, the radio receiver is necessary for removing.
Control panel heating and ventilation
The control panel is established by heating and ventilation in the central panel of furnish. The control panel incorporates cables to a heater and regulates temperature and distribution of streams of air on car salon. For access to cables it is necessary to remove a part of the dashboard previously.
Removal
|
|
| 1. Disconnect a wire from the negative plug of the storage battery.
2. Remove a safety cushion of the driver.
3. Remove a steering wheel, the switch of a signal of turn and, the top and bottom casings of a steering column.
|
|
4. Remove a combination of devices.
- Turn out three screws of fastening of furnish of a combination of devices.
- Turn out four screws.
- Extend a combination of devices from the dashboard.
- Disconnect two sockets from a combination of devices.
- Remove a combination of devices.
|
|
|
5. Remove the central console. |
|
|
- Separate a back cover from the console.
- Turn out two screws of fastening of a forward cover.
- Disconnect the electric socket.
- Turn out eight screws of fastening of the console.
|
6. Uncover the central panel and disconnect the electric socket from a back part of furnish of the central panel.
7. Remove a radio receiver.
- Turn out four screws of fastening of a radio receiver.
- Disconnect from a back part of a radio receiver the electric socket and an aerial cable.
|
|
8. Turn out two screws and disconnect the electric socket from a back part of the left bottom panel of furnish. |
|
|
9. Remove the right bottom panel of furnish. |
|
|
- Remove two condensing rings from assembly of a ware box.
- Turn out two screws and one nut of fastening of the top part of the right bottom panel of furnish.
- Turn out two bolts of fastening of the right bottom panel of furnish.
|
|
|
10. Remove the central panel.
- Turn out five screws of fastening of the central panel.
- Disconnect from a back part of the central panel the electric socket.
|
|
|
11. Remove the dashboard.
- Turn out two bolts of fastening of the left side of the dashboard.
- Turn out two bolts of fastening of the right side of the dashboard.
- Turn out two bolts of fastening of the central part of the dashboard.
- Turn out two bolts of fastening of a safety cushion of the forward passenger.
- Disconnect the electric socket.
|
|
|
Installation
|
|
|
|
1. Establish the dashboard.
- Establish the dashboard in a starting position.
- Be convinced that the steering column is established correctly through T-shaped with a plait of wires before dashboard installation. Otherwise the steering column cannot be correctly established.
- Connect sockets of a plait of wires and the dashboard. Sockets of plaits of wires are located so that they are combined with dashboard sockets.
- Establish a safety cushion of the forward passenger and fix it two bolts.
- Screw two bolts of fastening of the central part of the dashboard.
- Screw two bolts of fastening of the right side of the dashboard.
- Screw two bolts of fastening of the left side of the dashboard.
|
|
|
2. Establish the central panel.
- Connect the electric socket
- Screw five screws of fastening of the central panel.
|
|
|
3. Establish the right bottom panel of furnish.
- Screw two bolts of fastening of the right bottom panel of furnish.
- Screw two screws and one nut of fastening of the top part of the right bottom panel of furnish.
|
|
|
Establish two condensing rings on assembly of a ware box. |
|
|
4. Screw two screws and connect the electric socket to a back part of the left bottom panel of furnish. |
5. Establish a radio receiver.
- Connect to a back part of a radio receiver the electric socket and an aerial cable.
- Insert a radio receiver on a place and fix it four screws.
6. Connect the electric socket to a back part of furnish of the central panel and establish furnish of the central panel.
|
|
7. Establish the central console.
- Establish the central console and fix it eight screws.
- Connect the electric socket.
- Screw two screws of fastening of a forward cover.
- Fix a back cover to the console.
|
|
|
8. Establish a combination of devices.
- Establish a combination of devices to the dashboard and connect two sockets.
- Screw four screws of fastening of a combination of devices.
- Establish furnish of a combination of devices and fix it three screws.
|
9. Establish a steering wheel, the switch of a signal of turn both the top and bottom casings of a steering column.
10. Establish a safety cushion of the driver.
11. Connect a wire to the negative plug of the storage battery.
|
|
|