Heater of back glass. KIA Magentis/Optima (since 2000 of release)
Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
9. Power shafts, axes
10. Suspension bracket
11. Steering
12. Brake system
13. Body
14. Central air
15. Electric equipment
15.1. Specifications
15.2. Charging system
15.3. Power failure check on a wire connecting the storage battery to the generator (V6 engine)
15.4. Check of the current developed by the generator
15.5. Check of developed tension
15.6. Power failure check on a wire connecting the storage battery to the generator (the engine of 2,0 l)
15.7. Check of the current developed by the generator (the engine of 2,0 l)
15.8. Check of developed tension (the engine of 2,0 l)
15.9. Generator
15.10. Storage battery
15.11. Survey of the storage battery
15.12. Start system
15.13. Removal and starter installation
15.14. Transceiver installation
15.15. Removal and installation of remote control
15.16. Removal and audioblock installation
15.17. Multipurpose switch
15.18. Safety locks
15.19. Combination of devices
15.20. Switch of position of the parking brake
15.21. Heater of back glass
15.22. Screen wiper and stekloomyvatel of a windscreen
15.23. Safety cushions (SRS)
15.24. Precautionary labels
15.25. Safety cushion of the driver and spiral wire
15.26. Safety cushion of the forward passenger
15.27. Search and elimination of malfunctions of system of a charging
15.28. Search and elimination of malfunctions of system of start of the engine
16. Electric circuits
 










15-21-obogrevatel-zadnego-stekla.html

15.21. Heater of back glass

Defrosting of back glass is carried out by a heater which represents a number of the parallel conductors which have been raised dust on glass. At a transmission of an electric current conductors heat up and defreeze and clean off back glass from moisture. The current moves from the relay located in the block of safety locks of a motor compartment. If glass on was cleared in 15 minutes, it is necessary to include repeatedly a heater on the second cycle, i.e. for 15 minutes.

Check

 PERFORMANCE ORDER

For check of a heater of back glass wrap up щуп the voltmeter an aluminum or tin foil to prevent damage of a current-carrying strip of a heater. For definition of break it is necessary to press a finger a foil and to move it along a current-carrying strip.

1. Start the engine and include a heater of back glass. Connect negative щуп the voltmeter to "mass" of the car. In turn connect щуп the voltmeter to the center of each current-carrying strip of a heater of back glass. The voltmeter should show tension about 6 Century.

2. If the voltmeter shows tension 12 In, means, the current-carrying strip of a heater has break from outside between a point of connection of the voltmeter and the party of the heater connected to "weight".

3. If the voltmeter shows tension below 0 In, means, the current-carrying strip of a heater has break from outside between a point of connection of the voltmeter and the party of the heater connected to the positive plug of the storage battery.

4. For definition of a point of a gap move щуп on a current-carrying strip of a heater to the relevant party. A point where the tension shown by the voltmeter, sharply changed and is a gap place.

5. By an ohmmeter measure resistance of each current-carrying strip between the lateral plug of a heater and the center of each strip. The section of a strip having a gap, will have resistance twice above, than resistance of other strips of a heater.

Repair of a current-carrying strip of a heater

 PERFORMANCE ORDER

For repair of a current-carrying strip of a heater prepare the following materials and tools:

  • current-carrying weight;
  • melkodispersny current-carrying weight;
  • sticky tape;
  • solvent;
  • brush.

Solvent wipe glass area about a rupture of a current-carrying strip of a heater and paste strips of a sticky tape from two parties of a current-carrying strip.

Put with an interval in 15 mines three layers of current-carrying weight. Remove a sticky tape and wait, the current-carrying weight will not dry yet. In 24 hours with a sharp knife remove surpluses of current-carrying weight.

After restoration of a current-carrying strip of a heater purification of glass carry out along a strip of a heater a little humidified rags.


«on a step back
15.20. Switch of position of the parking brake
on the following page»
15.22. Screen wiper and stekloomyvatel of a windscreen