Code |
Element
|
|
Probable cause
|
P0713
|
Sensor of temperature of oil
|
Chain break
|
Sensor damage
|
P0712
|
If target tension of the sensor more than 4,57 In in 10 minutes (if the temperature of oil does not increase), is considered that there is a break of a chain of the sensor and the P0713 code registers
|
|
Socket damage
|
P0715
|
Sensor
of frequency of rotation of an entrance shaft
If no target impulse from the sensor of frequency of rotation of an entrance shaft on the 1st or 2nd transfer is found, at inclusion of the 3rd transfer for the speed more than 30 km/h are considered that the chain has break or short circuit and the P0715 code will be written down. If the P0715 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
Short chain short circuit / break
|
Sensor damage
Damage of the holder of lowering transfer
Socket damage TCM damage
|
P0720
|
The sensor
of frequency of rotation of a conducted shaft
If the target signal from the sensor of frequency of rotation of a conducted shaft for 50 % is lower than speed of the car on the 1st or at inclusion of the 3rd or 4th transfer speed more than 30 km/h are considered that the chain has break or short circuit and the P0720 code will be written down. If the P0720 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
Short chain short circuit / break
|
Damage of the sensor of provision of a butterfly valve
Socket damage
TCM damage Damage of the solenoidal valve
|
P0703
|
Switch of stoplights
If the switch
of stoplights burns more than 5 minutes at movement of the car it is considered that the chain has break or short circuit and the P0703 code will be written down.
|
Short chain short circuit / break
|
Damage of the switch
of stoplights
Socket damage TCM damage
|
P0750
|
Solenoidal valve of low transfer and backing transfer
|
Short chain short circuit / break
|
Damage
of the solenoidal valve
Socket damage TCM Damage
|
P0755
|
The solenoidal valve of raising transfer
|
Short chain short circuit / break
|
Damage
of the solenoidal valve
Socket damage TCM damage
|
P0760
|
Solenoidal valve of the second transfer
|
Short chain short circuit / break
|
Damage
of the solenoidal valve
Socket damage TCM damage
|
P0765
|
The solenoidal valve of lowering transfer
If too big or too small it is considered resistance of the solenoidal valve that the chain has break or short circuit and the corresponding code will be written down. As reliable criterion the 3rd transfer and a control lamp of N will be blocked will blink with frequency of 1 Hz.
|
Short chain short circuit / break
|
Damage
of the solenoidal valve
Socket damage TCM damage
|
P0743
|
Solenoidal valve of a damper of coupling (DCC)
|
Short chain short circuit / break
|
Damage
of the solenoidal valve of a damper of coupling
Socket damage TCM damage
|
P0740
|
Solenoidal valve of a damper of coupling (DCC)
If too small it is considered resistance of the solenoidal valve that the chain has break or short circuit and the P0743 code will be written down. If the factor of loading of a drive of the valve of the solenoid of management of shock-absorber coupling – 100 % during the continuous period is considered more than 4 seconds that there is a damage to a control system of coupling of the shock-absorber and the P0740 code will be written down. If the P0743 code is written down the 3rd transfer and a control lamp of N is blocked will blink with frequency of 1 Hz.
|
The system is faulty
|
Damage
of the solenoidal valve of a damper of coupling
Socket damage TCM damage
|
P0731
|
The transfer number of the 1st transfer does not correspond
to the specification
If the exit from the sensor of frequency of rotation of the conducted shaft, increased by transfer number of the 1st transfer does not correspond to an exit from the sensor of frequency of rotation of an entrance shaft the P0731 code will be written down. If the P0731 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
|
Damage of the sensor of frequency of rotation of an entrance shaft
Damage of the sensor of frequency of rotation of a target shaft
Damage of a brake of low transfer and backing transfer Damage of coupling of lowering transfer
|
P0732
|
The transfer number of the 2nd transfer does not correspond
to the specification
If the exit from the sensor of frequency of rotation of the conducted shaft, increased by transfer number of the 2nd transfer does not correspond to an exit from the sensor of frequency of rotation of an entrance shaft the P0732 code will be written down. If the P0731 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
|
Damage of the sensor of frequency of rotation of an entrance shaft
Damage of the sensor of frequency of rotation of a target shaft
Damage of coupling of lowering transfer Damage of coupling of raising transfer
|
P0733
|
The transfer number of the 3rd transfer does not correspond
to the specification
If the exit from the sensor of frequency of rotation of the conducted shaft, increased by transfer number 3-oh transfers does not correspond to an exit from the sensor of frequency of rotation of an entrance shaft the P0733 code will be written down. If the P0731 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
|
Damage of the sensor of frequency of rotation of an entrance shaft
Damage of the sensor of frequency of rotation of a target shaft
Damage of a brake of the 2nd transfer Damage of coupling of raising transfer
|
P0734
|
The transfer number of the 4th transfer does not correspond
to the specification
If the exit from the sensor of frequency of rotation of the conducted shaft, increased by transfer number of the 4th transfer does not correspond to an exit from the sensor of frequency of rotation of an entrance shaft the P0733 code will be written down. If the P0734 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
|
Damage of the sensor of frequency of rotation of an entrance shaft
Damage of the sensor of frequency of rotation of a target shaft
Damage of a brake of low transfer and backing transfer Damage of coupling of transfer of a backing
|
P0736
|
The transfer number of transfer of a backing does not correspond
to the specification
If the exit from the sensor of frequency of rotation of the conducted shaft, increased by transfer number of transfer of a backing does not correspond to an exit from the sensor of frequency of rotation of an entrance shaft the P0733 code will be written down. If the P0734 code four times is written down, the gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
|
Damage of the sensor of frequency of rotation of an entrance shaft
Damage of the sensor of frequency of rotation of a target shaft
Damage of a brake of low transfer and backing transfer
Damage of a brake of transfer of a backing Damage of coupling of transfer of a backing
|
P1723
|
Relay of management
of A/T
If tension on the relay of management of A/T less than 7 In the ambassador of inclusion of ignition, is considered that the chain has break or short circuit and the P1723 code will be written down. The gear wheel of the 3rd transfer will be blocked and the control lamp of N will blink with frequency of 1 Hz.
|
Short chain short circuit / break |
Damage
of the relay of management of A/T Socket damage TCM damage
|
P0708
|
SWITCH OF RANGES OF THE TRANSMISSION
Lack of a signal within more than 30 seconds More than two signals arrive continuously a current more than 30 seconds
|
|
Damage of the switch of ranges of a transmission
|