Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
8.1. Mechanical transmission
8.2. Automatic transmission
8.2.1. Specifications
8.2.2. Check of level of liquid in an automatic transmission
8.2.3. Liquid replacement in an automatic transmission
8.2.4. Replacement of the oil filter
8.2.5. Check of conductivity of the switch of ranges of a transmission
8.2.6. Check of conductivity of the switch of a sports mode (F4A42–2 2,0 and 2,5 l)
8.2.7. Switch of ranges of a transmission and adjustment of a cable of management
8.2.8. Check of components of an automatic transmission
8.2.9. Testing of collaboration of an automatic transmission and the engine on the motionless car (stall test)
8.2.10. Diagnostic codes
8.2.11. Diagnostics function
8.2.12. Inspection card of codes of diagnostics
8.2.13. The inspection card for determination of malfunctions
8.2.14. Adjustment of an axial gap of a reactionary brake
8.2.15. Adjustment of an axial gap of a brake of the second transfer
8.2.16. Adjustment of an axial gap of a brake of low transfer and backing transfer
8.2.17. Adjustment of an axial gap of a solar gear wheel of lowering transfer
8.2.18. Adjustment of preliminary loading of differential
8.2.19. Elements of a control system of a transmission
8.2.20. Removal and transmission installation
8.2.21. Transmission repair
9. Power shafts, axes
10. Suspension bracket
11. Steering
12. Brake system
13. Body
14. Central air
15. Electric equipment
16. Electric circuits
 










8-2-19-ehlementy-sistemy-upravleniya-korobkojj-peredach.html

8.2.19. Elements of a control system of a transmission

Removal

 PERFORMANCE ORDER

1. Turn out two screws of fastening of the forward panel.
2. After moving of forward seats turn out two screws of fastening of the panel.

3. Remove the forward panel together with two switches of heaters of seats.

4. Remove the lever panel.

5. Turn out two screws and remove the central panel, taking out her hand for the central part.

6. Disconnect the socket of a plug receptacle on 12 In from the central panel.

7. Turn out four screws and remove the console from an arm.
8. Remove a cable of moving and a short circuit cable.

9. Remove a clip of a cable of management and a pin from the selector lever.

10. Turn out bolts of fastening of the lever of the selector and disconnect the socket.

11. Remove the selector lever assembled.
12. Remove a clip and unscrew nuts with a fillet from the transmission parties.
13. Remove a cable of management of a transmission.

14. Remove a cable of moving and a short circuit cable.

Installation

 PERFORMANCE ORDER

1. Apply a thin film greasings on an internal part of the regulated plug.
Lubricant: SAE SAEJ310, NLGI No. 0

2. Move the lever of the selector and the switch of ranges of a transmission to situation N and establish a cable of management of a transmission.

3. At connection of a cable of management with an establishing arm of a transmission, establish a clip so that it contacted with a management cable in the situation shown in drawing.

4. Establish knot of the lever of the selector and connect the socket.
5. At connection of a cable of management to establishing an arm of the lever of the selector, establish a clip so that it contacted with a management cable.
6. Establish a management cable, a cable of short circuit and an assembly bolt a moving cable.
7. Establish the console and screw eight screws.

8. Connect the socket of a plug receptacle, establish the central panel and screw two screws.

9. Establish the lever panel.

10. Establish on the central panel two switches of a heater of seats.



«on a step back
8.2.18. Adjustment of preliminary loading of differential
on the following page»
8.2.20. Removal and transmission installation