Magentis and Optima repair since 2000 of release
1. Engines
2. Greasing system
3. Cooling system
4. Control and decrease in toxicity
5. Fuel system
6. Ignition system
7. Coupling
8. Transmission
8.1. Mechanical transmission
8.2. Automatic transmission
8.2.1. Specifications
8.2.2. Check of level of liquid in an automatic transmission
8.2.3. Liquid replacement in an automatic transmission
8.2.4. Replacement of the oil filter
8.2.5. Check of conductivity of the switch of ranges of a transmission
8.2.6. Check of conductivity of the switch of a sports mode (F4A42–2 2,0 and 2,5 l)
8.2.7. Switch of ranges of a transmission and adjustment of a cable of management
8.2.8. Check of components of an automatic transmission
8.2.9. Testing of collaboration of an automatic transmission and the engine on the motionless car (stall test)
8.2.10. Diagnostic codes
8.2.11. Diagnostics function
8.2.12. Inspection card of codes of diagnostics
8.2.13. The inspection card for determination of malfunctions
8.2.14. Adjustment of an axial gap of a reactionary brake
8.2.15. Adjustment of an axial gap of a brake of the second transfer
8.2.16. Adjustment of an axial gap of a brake of low transfer and backing transfer
8.2.17. Adjustment of an axial gap of a solar gear wheel of lowering transfer
8.2.18. Adjustment of preliminary loading of differential
8.2.19. Elements of a control system of a transmission
8.2.20. Removal and transmission installation
8.2.21. Transmission repair
9. Power shafts, axes
10. Suspension bracket
11. Steering
12. Brake system
13. Body
14. Central air
15. Electric equipment
16. Electric circuits
 










8-2-20-snyatie-i-ustanovka-korobki-peredach.html

8.2.20. Removal and transmission installation

 PERFORMANCE ORDER

1. Disconnect, first of all, a wire from the negative plug of the storage battery, then – from positive. Turn out a drain stopper and merge in suitable capacity transmission oil from a transmission.

2. Remove knot of the air filter.

3. Remove a management cable.
4. Disconnect the socket from the sensor of speed of the car.

5. Disconnect the socket from the switch of ranges of a transmission, the solenoidal socket and the socket from the sensor of temperature of oil.

6. Disconnect a hose from an oil radiator.
7. The special adaptation support the engine so that the weight of the engine was perceived by the adaptation.
8. Remove the stabilizer of cross-section stability, a tip of steering draft, the spherical hinge of the bottom lever and power shafts.

9. Turn out connecting sharnirny bolts of fastening of a transmission and assembly bolts of fastening of returnable pipes.

10. Turn out bolts and remove the bottom frame.

11. Remove a starter.
12. Turn out assembly bolts of fastening of a transmission.
13. Turn out bolts of fastening of a transmission to the engine.
14. Remove a transmission from the car.

Support of the engine and transmission should be established on the places without preliminary tension.

Sequence of installation of arms.

  1. Arm of installation of the engine.
  2. Top arm of a transmission.
  3. Arm of a back support.
  4. Arm of a forward support.

3. At installation of an arm of a forward support be careful not to damage a support that can lead to the increased vibration.

Installation

 PERFORMANCE ORDER

1. Establish on a forward part of a transmission the hydrotransformer and establish a transmission to the engine.

If the hydrotransformer to establish at first on the engine, at installation of a transmission the sealing ring of a transmission can be damaged.

2. Establish a cable of management of a transmission and adjust as follows.

  • Move the lever of the selector and the switch of ranges of a transmission to situation N and establish a cable of management of a transmission.
  • At connection of a cable of management to establishing arm of a transmission, establish a clip so that it contacted with a management cable.
  • As adjusting nut choose any free wheeling in a cable of management and check that the lever of the selector moves smoothly.
  • Check that the cable of management is adjusted correctly.

3. Installation is carried out to sequences of return to removal.


«on a step back
8.2.19. Elements of a control system of a transmission
on the following page»
8.2.21. Transmission repair